Condux Power Dart Blower Manuel d'utilisateur télécharger pdf (Page 2)

Operation Procedure

NOTE: Know the approximate length of the conduit run to

ensure the blowline is long enough to reach the destination.

1. Set the Power Dart

Blower on a clean, dry surface.

Ensure the power switches are accessible to the user

and the air inlets are not blocked.

2. Check that all 3 power switches are off before plugging in

the main power source.

3. Attach the air hose to the unit’s rear air outlet, and

attach the correct seal-off to the air hose’s other end.

4. Insert the blowline through the access hole on the rear

of the seal-off, and attach it to the line carrier or foam

carrier with a secure knot.

5. Adjust the drag plate on the rear of the seal-off to put a

slight drag on the blowline.

6. Place the line carrier or foam carrier into the duct and

then securely hold the seal-off in the duct opening.

7. Turn on one power switch at a time to avoid

overloading the circuit.

8. To control the carrier’s speed, remove the seal-off from

the duct—DO NOT GRAB THE BLOWLINE WITH YOUR

HAND.

9. Turn off the power switches when the carrier reaches its

destination.

The Condux

Power Dart

Blower uses three motors to

deliver a maximum of 300 ft

⁄min (8.5 m

⁄min) of forced air. It

easily blows poly line or measuring tape over 2,000' (610 m)

in up to 6" (152 mm) diameter conduit. The 110 VAC power

cord uses a 30 Amp-115 VAC twist plug to adequately

handle the motors’ electrical current requirements. The

220-240 VAC model is supplied with a 16 Amp-230 VAC

European plug. The unit requires an electrical outlet rated for

at least a 3,000-watt generator.

Weighing only 32 pounds (15 kilograms), the unit can be set

up in any indoor location with ease. The complete kit

includes the Power Dart Blower Unit, 25' (7.6 m) air hose,

Body Seal-Off & Seal-Offs for

⁄

"-6" (13 mm-152 mm)

Conduit. An optional accessory bag is also available.

120 VAC model uses (3) 7.3 Amp motors

220-240 VAC model uses (3) 4.2 Amp motors

The Condux

Power Dart

Blower is designed for safe opera-

tion, however, these safety precautions must be followed:

1. Wear personal protective equipment: hard hat,

safety glasses, safety shoes, and leather work gloves.

2. Follow all standard access vault opening procedures,

including work area protection and gas detection.

3. Be aware of all utility lines in the immediate area and do

not work around live circuits.

4. Warning: To reduce the risk of fire or electric shock, do

not use unit with any solid state speed control device.

5. Indoor use only. Do not operate in or near water. Do

not set the Power Dart

Blower on a wet surface or

expose it to rain.

6. Turn power switches off before connecting or

disconnecting any electrical cords.

7. Ensure the electrical outlet or generator is rated for at

least 3,000 watts—a fire could result from wiring

overheating.

8. Do not remove or modify the 30 Amp-115 VAC twist

plug, or the 16 Amp-230 VAC European plug.

General Information

Safe Operating Practices

Tool Setup

!WARNING: Read and understand all

procedure and safety instructions before

using the Condux

Power Dart

Blower.

Failure to do so may result in serious

personal injury or death.

!CAUTION: Wear personal protective

equipment: hard hat, safety glasses,

safety shoes, and leather work gloves.

!ADVERTENCIA: Favor de leer y

comprender todas las instrucciones de

operación y seguridad antes de usar el

Condux

Power Dart

Blower. Si Ud. no

comprende las instrucciones favor de

consultarle a su jefe.

ADVERTENCIA

Instrucciones

de Operación

SAVE THIS USER’S GUIDE FOR FUTURE REFERENCE.

1. No user serviceable parts inside. Do not remove outer

shell from the unit. For product service, consult factory.

2. If supply cord is damaged, it must be replaced by the

manufacturer or its service agent or similarly qualified

individual.

Service

1. Keep Power Dart Blower, Seal-Off, Hose and various

carriers clean and dry for proper operation. Wipe

excess dirt off with a soft cloth.

2. Do not pressure wash or use petroleum based solvents

on the Power Dart Blower or accessories.

Cleaning Instructions

!WARNING: For continued protection

against risk of fire, replace only with same

type and rating of fuse (refer to

Replacement Parts List).

1 2 3 4

Commentaires sur ces manuels

Pas de commentaire

Condux Power Dart Blower Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Condux Power Dart Blower